Seite 16 von R/D Tech Prüfköpfe für Rohrprüfung von Olympus NDT

eddy current probes tek high-resolution attached features ·.lightweight.and.solid.construction ·.coil.protected.with.a.plastic.sleeve ·.steel.wear.guides.at.front.and.rear.ends ·.narrow.coil ideal.for.thin.tubing.inspections.like.titanium.tubing catalog part number tek.­.xxx.­.005.­.nyy tek.­.xxx.­.010.­.nyy tek.­.xxx.­.015.­.nyy tek.­.xxx.­.025.­.nyy tek.­.xxx.­.030.­.nyy tek.­.xxx.­.050.­.nyy tek.­.xxx.­.075.­.nyy tek.­.xxx.­.100.­.nyy tek.­.xxx.­.125.­.nyy tek.­.xxx.­.150.­.nyy tek.­.xxx.­.250.­.nyy tek.­.xxx.­.300.­.nyy tek.­.xxx.­.500.­.nyy tek.­.xxx.­.600.­.nyy xxx yy probe outside diameter in mm in 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 9 .6.to.50 0 .380.to.1 .970 frequency range khz 1.to.10 2.to.20 3.to.30 5.to.50 6.to.60 10.to.100 15.to.150 20.to.200 25.to.250 30.to.300 50.to.500 60.to.600 100.to.1000 120.to.1200 cable length in m ft 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 15 20 and.30 49 .2 65 .6 and.98 .5 probe.size.in.millimeters.rounded.to.the.nearest.0 .2.mm.multiple for.example 12 .6.mm.corresponds.to.126 see.table.1.on.page.24.for size.recommendations see.table.2.on.page.25.to.select.the.probe.frequency cable.length standard.length.is.15.m above.probes.use.a.4-pin.amphenoltm.connector for.a.6-pin.jaeger.connector add.the.letter.j.at.the.end.of.the.probe.number example if.the.tube.dimensions.are.25 .4.mm 1.in od.x.0 .71.mm 0 .028.in wt and.the.tube.is.made.out.of.stainless.steel.316 then.the.probe should.have.a.22 .8.mm.diameter.and.500.khz.frequency tek-228-500-n15 .

[schliessen]